Battery Bracket Installation Instructions

Thank you for purchasing a Bracket Boyz product. The instructions below is a general installation guide for our 20L, 30L lay down, and 30L upright battery bracket.

Package contents

Battery Bracket

1 X bottom plate

2 X side plates

1 X top plate

4 X M6 cage nuts and cap screws (for top plate)

4 x M6 cap screws and serrated nuts (for bottom plate)

1 X vibration pad (for bottom plate)

1 x vibration strip (for corners of side brackets)

Optional parts/add ons

-Killswitch

-Killswitch bracket (w/ M4 hardware)

-Killswitch bezel (w/ M6 hardware)

-Killswitch key

-Breaker or fuse (w/ M4 hardware)

-Radlok pins (for terminal posts)

-Radloks (0 to 4 gauge size)

-Red Rubber Boots

-SCL Heatshrink

-Ring Terminal Lugs

30L Lay Down Battery Bracket

30L Lay Down Bracket

30L Vertical Battery Bracket

30L Upright Bracket

20L Battery Bracket

20L bracket

Tools required:

-Rivnut gun

-0-8 gauge crimper

-Heat Gun

-10mm box wrench

-2.5mm and 4mm allen keys

* Rivnut gun is required for installation of optional fuses/breakers and killswitch bracket to the side brackets. If you do not have one you can email us about our mounting service.

* A cable lug crimper for #0, #2 , #4, or #8 gauge cable is needed to install Radloks or ring terminals. If you do not have this crimper you can email us for our crimping service.

* A heat gun is needed to install the SCL heats shrinks on the terminated connectors. If you do not have a heat gun you can email us for our heat shrinking service.

Assembly

If you did not purchase a breaker/fuse and/or killswitch bracket you can skip to step 3

Install rivnuts on the sideplates for the hole patterns of the breaker/fuse and/or killswitch bracket This is illustrated in fig 1A to 1C. The rivnuts go in from the inside portion (side facing the battery) of the side brackets.
Install the accessory using the M4 hardware provided. If you have a 200 amp breaker or a Blue Sea fuse holder, these will need to drilled with a 6mm or 15/64 drill bit.
Install the cage nuts on the side plates. These clip on the rectangular cut out on the side plates. This will be the top side of the bracket. Install the top plate with the M6 cap screws - do not tighten all the way.
Place the battery on top of the bottom plate then place the partially assembled bracket (top plate and side plates) over the battery. Certain battery models will need the antivibration pads on the corners of the side plates and on the bottom plate. Install as needed.
Push the side brackets snug to the battery and install the side plates onto the bottom plate using the provided M6 hardware. The cap screws come up from the bottom of the plate with the serrated locking nuts on the top side of the side brackets.
Tighten the top plate by snugging the side brackets in and centering the cage nuts and M6 hardware.
If you have a killswitch, mount the killswitch from the bottom and place the bezel on top and use the M6 caps screws to install figure 2A. If you did not purchase the bezel, use the flanged nuts provided.

30L Lay Down Battery Bracket

Battery Bracket Installation Instructions

Thank you for purchasing a Bracket Boyz product. The instructions below is a general installation guide for our 20L, 30L lay down, and 30L upright battery bracket.

Package contents

Assembly

Install rivnuts on the sideplates for the hole patterns of the breaker/fuse and/or killswitch bracket This is illustrated in fig 1A to 1C. The rivnuts go in from the inside portion (side facing the battery) of the side brackets.

Install the accessory using the M4 hardware provided. If you have a 200 amp breaker or a Blue Sea fuse holder, these will need to drilled with a 6mm or 15/64 drill bit.

Install the cage nuts on the side plates. These clip on the rectangular cut out on the side plates. This will be the top side of the bracket. Install the top plate with the M6 cap screws - do not tighten all the way.

Place the battery on top of the bottom plate then place the partially assembled bracket (top plate and side plates) over the battery. Certain battery models will need the antivibration pads on the corners of the side plates and on the bottom plate. Install as needed.

Push the side brackets snug to the battery and install the side plates onto the bottom plate using the provided M6 hardware. The cap screws come up from the bottom of the plate with the serrated locking nuts on the top side of the side brackets.

Tighten the top plate by snugging the side brackets in and centering the cage nuts and M6 hardware.

If you have a killswitch, mount the killswitch from the bottom and place the bezel on top and use the M6 caps screws to install figure 2A. If you did not purchase the bezel, use the flanged nuts provided.